Cross Hatch Cutter Adhesion Test Kit with Guide Wheel – CC3000 Range

1 4

About Cross Hatch Cutter Adhesion Test Kit with Guide Wheel – CC3000 Range

The Cross Hatch Adhesion Test Kit CC3000 is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates.

The cutting depth of the Cross Hatch Cutter within the CC3000 range can be adjusted while the cutter is guided by two ball bearings to ensure reproducible results and the depth of the cutter is adjustable to measure coatings up to 250 µm thick.

Directions for use:

Simply make a cutting pass through the coating to the substrate, this will leave 6 parallel cuts in the coating. Then make a second pass at 90º to the first to make a square lattice pattern.  Apply a length of adhesive tape over the lattice pattern & remove tape within 5 minutes.  You can then classify the test area using the supplied magnifier to the relevant national standard.

Applications

CC3000 Cross Hatch Cutter Adhesion Test Kit with Guide Wheel Close up on test panel

  • Testing adhesion of dry coats of paint on substrates

Specifications

CC3000 Cross Hatch Cutter Adhesion Test Kit with Guide Wheel Blade Close UpISO 2409:

  • 1 mm. spacing for coatings up to 60 µm on hard substrates
  • 2 mm. spacing for coatings up to 60 µm on soft substrates
  • 2 mm. spacing for coatings from 61 to 120 µm on both hard and soft substrates
  • 3 mm. spacing for coatings from 121 µm to 250 µm on both hard / soft substrates

ASTM D3359:

  • 1 mm. spacing for coatings up to 50 µm
  • 1,5 mm. spacing for coatings from 50 to 125 µm

Packing List:

  • Cross Hatch Adhesion Tester with Single Headed Cutting Knife & Guide Wheel
  • Brush
  • Illuminated Loupe
  • Roll of Adhesive Tape to ISO 2409

All Downloads

Filename Size Download
Cross Hatch Adhesion Tester CC3000 Range Product Data Sheet 0.49MB Download

Ordering Information

Part Number Description
Cross Cut Adhesion Test Kit acc. to ISO 2409 , 6 blades
55-SP1680 CC3000 cross-cut tester 1mm ISO 2409
55-SP1681 CC3000 cross-cut tester 2mm ISO 2409
55-SP1682 CC3000 cross-cut tester 3mm ISO 2409
Cross Cut Adhesion Test Kit acc. to ASTM D3359, 11 blades
55-SP1683 CC3000 cross-cut tester 1mm to ASTM
55-SP1684 CC3000 cross-cut tester 1.5mm to ASTM

A range of accessories is available for this product:

Part Number Description
70-K0001539M002 ISO2409 adhesive tape (1 roll)
70-K0001539M001 ASTM D3359 Adhesive Tape (1 roll)
55-SP1702 ISO Spare Blade 1mm
55-SP1703 ISO Spare Blade 2mm
55-SP1704 ISO Spare Blade 3mm
55-SP1705 ASTM Spare Blade 1mm
55-SP1706 ASTM Spare Blade 1.5mm
  • Last updated: May 2024
  • Version: 1.0

Statements, technical information and recommendations contained herein are based on tests we believe to be reliable but they are not to be construed in any manner as warrantees expressed or implied. The user shall determine the suitability of the product for his intended use and the user assumes all risk and liability whatsoever in connection therewith.